Cisco CCNA 200-301 Practice Test

Cisco Practice Tests

Question 1 / 55 - Mode : Exam
In what security zone are the public web servers located? A. DMZ B. Inside C. Outside D. Campus Which of these should be checked when troubleshooting end-to-end connectivity between IP addresses? (Choose three) A. The physical connection B. The default gateway C. The domain name resolution address D. The computer name E. The routing protocol Which ICMP for IPv6 message types are informational messages? (Choose two) A. Packet too big B. Time exceeded C. Echo request D. Echo reply E. Destination unreachable https://www.learncisco.net/courses/icnd-1/introducing-ipv6/ipv6-header-and-icmp.html Identify the commands required to verify both - the IP addresses of a switch and a host. (Choose two) A. show interface status B. show ip interface brief C. ipconfig /renew D. ipconfig /release E. ipconfig /all https://www.learncisco.net/courses/icnd-1/lan-connections/starting-a-router.html What is the name of the protocol that is used by IEEE 802.1x devices to communicate with the authenticator and authentication server? A. EAP B. EAPoL C. RADIUS D. TACACS+ What command is used to configure IPv6 static route? A. ipv6 route ::/0 outgoing interface ipv6 next hop B. ipv6 route ipv6 network/ipv6 mask ipv6 next hop C. ipv6 route ipv6 network/ipv6 mask outgoing interface ipv6 next hop D. ipv6 route ::/0 ipv6 next hop https://www.learncisco.net/courses/icnd-1/introducing-ipv6/ipv6-connectivity.html To connect a Cisco wireless LAN controller to a wired network, which of the following would you use? Assume that this connection will carry traffic to and from APs. A. Console port B. Service port C. Distribution system port D. AP data port What statements describe the purpose and functions of VLANs for improving a poorly designed network? (Choose three) A. The prevention of specific users within one VLAN from accessing a designated remote server B. The option to group stations that are segmented logically by functions or groups C. The ability to implement access and security policies within particular groups of users D. The flexibility of implementing VLANs across multiple floors E. The provision of protocols and port numbers https://www.learncisco.net/courses/icnd-1/medium-size-switched-network-construction/vlans-and-trunk.html Which command is used to view the neighbor discovery table on a PC? A. show ipv6 neighbor B. show ipv6 neighbors C. netsh interface ipv6 show neighbor D. netsh interface ipv6 show neighbors Which of the following are available methods of classifying packets in DiffServ on Cisco routers? (Choose three) A. Matching the IP DSCP field B. Matching the 802.1p CoS field C. Matching fields with an extended IP ACL D. Matching the SNMP Location variable Which of the following OSPF packet types ensures reliable transport and exchange of information? A. link-state acknowledgement, or LSAck B. link-state update, or LSU C. link-state request, or LSR D. database description package, or DBD https://www.learncisco.net/courses/icnd-2/an-overview-of-ospf/link-state-databases.html What is the name of the firewall feature that, when used, can maintain a historical database of each connection through a device: Where it was sourced, destined, and which protocol and protocol port it was using? A. Stateless Inspection B. Stateful Inspection C. Network Protocol Analysis D. Protocol State Analysis You are troubleshooting a connectivity issue on the Branch router when you realize that a ping test to the destination network is not successful. The Branch and corresponding HQ router have their neighbor adjacency set up. What could be the problem? (Choose two) A. The HQ router isn't advertising the route B. There is an OSPF area mismatch C. The HQ router is not enabled for OSPF D. There is a route missing to the destination in the Branch router`s routing table E. Layer 2 connectivity is not established between the two routers https://www.learncisco.net/courses/icnd-2/troubleshooting-basic-connectivity/troubleshooting-connectivity.html Using the exhibit as a reference, how many JSON objects are there? A. 11 B. 1 C. 2 D. 12 R1, R2, R3, and R4 have their Fast Ethernet 0/0 interfaces attached to the same VLAN. A network engineer has typed a configuration for each router by using a word processor. He will later copy and paste the configuration into the routers. Examine the following exhibit, which lists configuration for the four routers, as typed by the network engineer. Assuming that all four routers can ping each other’s LAN IP addresses after the configuration has been applied, choose the routers that will be able to form a neighbor relationship with the other routers on the LAN. (You can assume that, if not shown in the exhibit, all other related parameters are still set to their defaults.) (Choose two) A. R1 B. R2 C. R3 D. R4 E. None of the routers will exchange routing information. What is the name of the protocol that has been developed by the ONF that is used to communicate between an SDN controller and the network devices it controls? A. OpFlex B. OpenSDN C. SbControl D. OpenFlow Host A and Host B sit in two different subnets. The path between the subnets of these two hosts runs through three different Layer 3 forwarding devices (routers and Layer 3 switches). A network engineer uses the APIC-EM Path Trace ACL Analysis tool to analyze the path used for Host A to send packets to Host B. Which part of the function is done specifically by the ACL Analysis or ACL Trace part of the tool? A. Discovery of the topology that exists between the two hosts B. Analysis of the Layer 3 forwarding decisions in the path from Host A to B C. Analysis of the Layer 2 forwarding decisions in the path from Host A to B D. Analysis of the impact of ACLs on the packets that would flow from Host A to B You want to verify the Cisco IOS software version, ROM version, amount of memory, type of processor, number and types of interfaces, as well as the configuration register value on your 2900 series IOS router. What command will allow you to accomplish this? A. Show startup-configuration B. Show running-configuration C. Show version D. Show flash When comparing controller-based networks and traditional networks what are some perceived benefits from a controller-based perspective? (Choose two) A. New operational models that allow the entire network to be instantiated and not just a single device at a time B. The use of automation through APIs that enable data-driven models C. New operational models that allow for a single device to be instantiated with the entire network in mind D. The use of legacy approaches in the network to increase efficiency and productivity Which command correctly assigns a subinterface to VLAN 8 using 802.1Q trunking? A. Router(config-if)#encapsulation 802.1Q vlan 8 B. Router(config-if)#encapsulation dot1q 8 C. Router(config)#encapsulation 8 dot1q D. Router(config)#encapsulation trunk dot1q 8 https://www.learncisco.net/courses/icnd-1/medium-size-switched-network-construction/vlans-and-trunk.html Which IOS command always displays OSPF hello timer settings? A. show ip protocols B. show ip route C. show ip ospf interface D. show ip ospf neighbor E. debug ip ospf events Given the output from a working OSPF router, as seen in the exhibit, how many neighboring routers exist? B. 1 C. 2 D. 3 E. More than 3 Which application(s) would Jitter and Delay not be a concern for the users experience? A. Online Gaming. B. VoIP. C. Web browsers. D. videoconferencing. Which statement is true about the addresses 172.16.0.255/23 and 172.16.1.0/23? A. The address 172.16.0.255/23 is a directed broadcast address B. The addresses are in different subnets C. The address 172.16.1.0/23 is a subnet ID D. The addresses are in the same subnet Which DSCP marking group was created to be backward compatible with Internet Protocol Precedence (IPP) values? A. EF B. AF C. CS D. PF Which of the following cloud services is most likely to be used for software development? A. IaaS B. PaaS C. SaaS D. SLBaaS A Cisco Catalyst switch connects to what should be individual user PCs. Each port has the same port security configuration, configured as follows: interface range gigabitethernet 0/1 - 24 switchport mode access switchport port-security switchport port-security mac-address sticky Which of the following answers describe the result of the port security configuration created with these commands? (Choose two) A. Prevents unknown devices with unknown MAC addresses from sending data through the switch ports. B. If a user connects a switch to the cable, prevents multiple devices from sending data through the port. C. Will allow any one device to connect to each port, and will save that device’s MAC address into the startup-config D. Will allow any one device to connect to each port, but will not save that device’s MAC address into the startup-config You are upgrading the Cisco IOS on your Catalyst switch. While browsing the available downloads on Cisco's website, you notice that you need the model of the switch to obtain the correct IOS. Which command can you issue on your IOS switch to identify the model? A. show running-config B. show flash C. show startup-config D. show platform nvram E. show version F. show processes Review the following router configuration and identify the correct statements regarding telnet access to the router: Router(config)#access-list 1 deny host 10.1.20.1 Router(config)#access-list 1 deny host 10.1.20.2 Router(config)#access-list 1 permit host 10.1.10.1 Router(config)#access-list 1 permit host 10.1.10.2 Router(config)#access-list 1 permit 10.1.20.0 0.0.0.255 Router(config)#line vty 0 4 Router(config-line)#access-class 1 in (Choose two) A. Telnet access from all hosts in the 10.1.20.0/24 network is denied except 10.1.20.1 and 10.1.20.2 B. Telnet access from hosts 10.1.20.1 and 10.1.20.2 is allowed C. Telnet access from hosts 10.1.10.1 and 10.1.10.2 is allowed D. Telnet access from all hosts in the 10.1.10.0/24 network is allowed E. Telnet access from all hosts in the 10.1.20.0/24 network is allowed except 10.1.20.1 and 10.1.20.2 F. Telnet attempts that are denied will generate a syslog message What source will be chosen when a destination network offers multiple sources? A. The dynamic route B. The route with the highest metric C. The source with the lowest administrative distance D. The static route https://www.learncisco.net/courses/icnd-1/lan-connections/functions-of-routing.html Identify the command used to show the status of a specific interface. A. show interfaces description B. show interfaces type module/slot/port C. show interfaces hardware D. show interfaces load https://www.learncisco.net/courses/icnd-1/network-environment-management/neighbors-on-the-network.html Of the figures shown, which depicts an accurate Clos Architecture? A. Topology A B. Topology B C. Topology C D. Topology D What will happen if a private IP address is assigned to a public interface connected to an ISP? A. Addresses in a private range will be not be routed on the Internet backbone. B. Only the ISP router will have the capability to access the public network. C. The NAT process will be used to translate this address to a valid IP address. D. A conflict of IP addresses happens, because other public routers can use the same range. https://www.learncisco.net/courses/icnd-1/building-a-network/tcpip-internet-layer.html Refer to the diagram. What method of authentication is being used? A. Open authentication B. CCMP C. WEP D. 802.1x Assuming the default switch configuration, which VLAN range can be added, modified, and removed on a Cisco switch? A. 1 through 1001 B. 2 through 1001 C. 1 through 1002 D. 2 through 1005 https://www.learncisco.net/courses/icnd-1/ethernet-lans/starting-a-switch.html What is the alternative notation for the IPv6 address B514:82C3:0000:0000:0029:EC7A:0000:EC72? A. B514 : 82C3 : 0029 : EC7A : EC72 B. B514 : 82C3 :: 0029 : EC7A : EC72 C. B514 : 82C3 : 0029 :: EC7A : 0000 : EC72 D. B514 : 82C3 :: 0029 : EC7A : 0 : EC72 https://www.learncisco.net/courses/icnd-1/introducing-ipv6/the-ipv6-address.html Which statements describe the characteristics of port security? (Choose two) A. Sticky learning adds dynamically learned addresses to the running configuration B. Ports configured with port security only accept frames from addresses that have been learned or the ones that have been configured C. Addresses must be manually added to the switch D. It restricts port access using IP addresses https://www.learncisco.net/courses/icnd-1/ethernet-lans/switch-security.html An engineer connects to Router R1 and issues a show ip ospf neighbor command. The status of neighbor 2.2.2.2 lists FULL/BDR. What does the BDR mean? A. R1 is an Area Border Router. B. R1 is a backup designated router. C. Router 2.2.2.2 is an Area Border Router. D. Router 2.2.2.2 is a backup designated router. Which command is used to apply an ACL to an interface? A. access-group B. ip access-group C. ip access-list D. ip access-class E. access-class F. access-list Which command is used to create a standard numbered IPv4 ACL? A. access-list numbered B. ip access-list C. numbered access-list D. access-list ip E. access-list __________ means that the QoS tool changes one or more header fields, setting a value in the header. A. Marking B. Classifying C. Insertion D. Qualifying What is the name of the Cisco product that offers a number of rack-mountable server configurations intended to be used in data centers? A. ASA B. KVM C. CRC D. UCS You have changed the domain name for one server in a VTP domain to Sales. What happens to other servers with a domain name of null in the same VTP domain area? A. They will have a domain name of Sales B. They will need to have their domain name manually set C. They will display an error D. They will retain a domain name of null Which of the following is required when configuring port security with sticky learning? A. Setting the maximum number of allowed MAC addresses on the interface with the switchport port-security maximum interface subcommand B. Enabling port security with the switchport port-security interface subcommand C. Defining the specific allowed MAC addresses using the switchport port-security mac-address interface subcommand D. All the other answers list required commands With IEEE 802.1x, which role does a LAN switch typically play? A. Authentication server B. Supplicant C. Translator D. Authenticator What will the solicited node multicast address be for the IPv6 address 2001:DB8:1001:F:2C0:10FF:FE17:FC0F? A. FF02:0000:0000:0000:0000:10FF:FE17:FC0F B. FF02:0000:0000:0000:0000:0001:FF17:FC0F C. 2001:0000:0000:0000:0000:0001:FF17:FC0F D. FF02:0000:0000:0000:0000:0001:FE17:FC0F What does a 2900 ISR do if the POST is successful during start up, but there is no configuration file to load? A. It shuts down B. It creates a configuration file with default settings and loads user EXEC mode C. It initiates the system configuration dialog D. It reboots E. It enters ROMMON mode What command should you configure globally to enable a 15-minute recovery time for the port security errdisable state? A. errdisable recovery interval 15 B. errdisable recovery timer 15 C. errdisable recovery timer 900 D. errdisable recovery interval 900 What options are required criteria for a service to be a cloud service? (Choose two) A. Broad network access B. Resource pooling C. Agile network access D. Proactive service Which IPv6 header field specifies the maximum number of hops that an IPv6 packet can take? A. Flow label B. Time to live C. Next header D. Hop limit E. Traffic class F. Extension header What value is primarily used to determine which port becomes the root port on each nonroot switch in a spanning-tree topology? A. path cost B. lowest port MAC address C. VTP revision number D. highest port priority number E. port priority number and MAC address https://www.learncisco.net/courses/icnd-2/vlans-and-spanning-tree/spanning-tree-operations.html Which of the following messages in the DHCP process are broadcasted? (Choose two) A. Request B. Offer C. Discover D. Acknowledge What is the purpose of subnetting? A. To translate an IPv4 address into an IPv6 address B. To take multiple networks and combine them into a single larger network C. To take a Class A network and turn it into a Class B or Class C network D. To translate a public IPv4 address into a private IPv4 address E. To take a single network and divide it into multiple smaller networks Which statements describe the benefits of using a variable-length subnet mask? (Choose two) A. It provides a better-defined network hierarchy within an address plan B. It ensures that only a single subnet mask within an entire Class is used C. It enables more efficient use of IP addresses D. It prevents aggregation of network addresses https://www.learncisco.net/courses/ccna/part-2-ip-addressing-and-subnetting-nat/variable-length-subnet-mask.html Which statement is true about the subnet masks /12, /20, and /28? A. They all have the same number of network bits B. They all have the same block size of 16 C. They all create only 16 subnets D. They all have the same number of host bits

Our Recommended Premium CCNA Training Resources

These are the best CCNA training resources online:

Click Here to get the Cisco CCNA Gold Bootcamp, the most comprehensive and highest rated CCNA course online with a 4.8 star rating from over 30,000 public reviews. I recommend this as your primary study source to learn all the topics on the exam.

Want to take your practice tests to the next level? AlphaPrep’s purpose-built Cisco test engine has the largest question bank, adaptive questions, and advanced reporting which tells you exactly when you’re ready to pass the real exam. Click here for your free trial.

The CCNA 200-301 is for the Cisco Certified Network Associate (CCNA) Implementing and Administering Cisco Solutions exam. You can use the practice test to check your knowledge and improve your understanding in preparation for the Cisco CCNA certification exam.

The Cisco CCNA 200-301 practice exam tests include questions to test your knowledge and skills related to Cisco networking fundamentals, which helps you pass the actual exam.

The Cisco CCNA exam objectives include Cisco network fundamentals on routers, switches, IP addresses, etc., network access, IP connectivity such as static and dynamic routing protocol, IP services, network security fundamentals, and automation and programmability.

Cisco CCNA 200-301 Practice Test

Complete this form to get your score report

Our Recommended Premium CCNA Training Resources